- Online Learning Support
- Application Support
- Audio/Visual Device Support
- Telephone\Voicemail support
- Wireless Support
Setup Windows 7/8/10 for COM Wireless
SETUP WINDOWS 7/8/10 FOR COM WIRELESS
These instructions apply to Windows 7/8/8.1/10 devices. You will use a setup wizard called Cloudpath XpressConnect to connect your device. You may also use these instructions to recreate your connection in the future. This may be necessary if you delete your connection or change your password. Please note that the "Com_Limited" wireless is for onboarding purpose ONLY. You must complete your setup to join your assigned wireless network.
Step 1: Enable wireless on your device If your Wifi is already enabled, go to Step 2. If disabled, follow instructions below.
Go to Control Panel.
Click the Network and Internet category and then select Networking and Sharing Center.
From the options on the left-hand side, select Change adapter settings.
Right-click on the icon for Wireless Connection
Click enable.....
Some devices may have a wireless hardware switch. Make sure it is unlocked.
Step 2: Connect to COM_Limited : Click the wireless icon located in the lower-right corner of your Windows device.
Select COM_Limited from the list of available networks (Do not select to connect automatically).
Click Connect.
Step 3: Select COM_Limited Within your Wi-Fi settings, select COM_Limited from your list of available networks.
The wireless login page will open automatically. This may take few seconds.
If that does not work, open any browser.
You should be directed to the wireless login page. If you are not redirected automatically, go to https://byod.marin.edu
The illustrations below show only Student configuration. Staff (Classified, Faculty, & Management) and Guest configurations are similar.
Select your appropriate network access: you may be either Guest, Student, or Staff.
Step 4: Terms and Conditions Read carefully the Terms & Conditions of using COM wireless
Check I accept the terms of the End-User License Agreement, if you agreed.
Click Start.
Click OK at the notification prompt.
Step 5: Login credentialsFor the username, enter your MyCOM username (not your email address).
Enter your MyCOM password in the password field. Only passwords are case-sensitive.
Click Continue.
Step 6: Download CloudPath applicationDownload the file, NetworkWizardLoader.exe
Once the file has downloaded click, "Run."
Step 7: Install the CloudPath application Start the installation
Continue through each of the subsequent installation steps.
If prompted by User Account Control for permission to make changes click on Yes.
A Security Warning will display requesting permission to install the certificate, click on Yes.
Once the setup has completed click Done.
Test connectivity by opening any new web address.
These instructions apply to Windows 7/8/8.1/10 devices. You will use a setup wizard called Cloudpath XpressConnect to connect your device. You may also use these instructions to recreate your connection in the future. This may be necessary if you delete your connection or change your password. Please note that the "Com_Limited" wireless is for onboarding purpose ONLY. You must complete your setup to join your assigned wireless network.
Step 1: Enable wireless on your device If your Wifi is already enabled, go to Step 2. If disabled, follow instructions below.
Go to Control Panel.
Click the Network and Internet category and then select Networking and Sharing Center.
From the options on the left-hand side, select Change adapter settings.
Right-click on the icon for Wireless Connection
Click enable.....
Some devices may have a wireless hardware switch. Make sure it is unlocked.
Step 2: Connect to COM_Limited : Click the wireless icon located in the lower-right corner of your Windows device.
Select COM_Limited from the list of available networks (Do not select to connect automatically).
Click Connect.
Step 3: Select COM_Limited Within your Wi-Fi settings, select COM_Limited from your list of available networks.
The wireless login page will open automatically. This may take few seconds.
If that does not work, open any browser.
You should be directed to the wireless login page. If you are not redirected automatically, go to https://byod.marin.edu
The illustrations below show only Student configuration. Staff (Classified, Faculty, & Management) and Guest configurations are similar.
Select your appropriate network access: you may be either Guest, Student, or Staff.
Step 4: Terms and Conditions Read carefully the Terms & Conditions of using COM wireless
Check I accept the terms of the End-User License Agreement, if you agreed.
Click Start.
Click OK at the notification prompt.
Step 5: Login credentialsFor the username, enter your MyCOM username (not your email address).
Enter your MyCOM password in the password field. Only passwords are case-sensitive.
Click Continue.
Step 6: Download CloudPath applicationDownload the file, NetworkWizardLoader.exe
Once the file has downloaded click, "Run."
Continue through each of the subsequent installation steps.
If prompted by User Account Control for permission to make changes click on Yes.
A Security Warning will display requesting permission to install the certificate, click on Yes.
Once the setup has completed click Done.
Test connectivity by opening any new web address.
DataImage38.png
DataImage38.png
DataImage57.png
DataImage57.png
DataImage57.png
DataImage57.png
DataImage73.png
DataImage73.png
DataImage73.png
DataImage73.png
DataImage76.png
DataImage76.png
DataImage89.jpg
DataImage89.jpg
DataImage93.png
DataImage93.png
DataImage93.png
DataImage93.png
DataImage93.png
DataImage93.png
| Files | ||
|---|---|---|
|
DataImage38.png 43.8 KB |
||
|
DataImage57.png 7.1 KB |
||
|
DataImage57.png 11.6 KB |
||
|
DataImage73.png 32 KB |
||
|
DataImage73.png 52.7 KB |
||
|
DataImage76.png 25.2 KB |
||
|
DataImage89.jpg 38.2 KB |
||
|
DataImage93.png 30.8 KB |
||
|
DataImage93.png 19.2 KB |
||
|
DataImage93.png 28.2 KB |
Get help for this page
Jitbit HelpDesk